Rollercam MOLLE Tie-Down Kit
Rollercam MOLLE Tie-Down Kit
The Rollercam MOLLE Tie-Down Kit is a set of ten 0.75-inch cam straps plus a Roperoller, sized to lash gear flat against a MOLLE panel. You get four 2-foot straps, four 3-foot straps, and two 6-foot straps, so short tool rolls and full-size traction boards both get a strap that fits. The Roperoller 2-pack and two 10-foot sections of 3mm accessory cord handle the odd-shaped stuff a flat strap won't.
The straps run UV-stabilized polypropylene webbing with triple-bar tack stitching and T-135 polyester thread. Each cam buckle holds a 95-pound working load; the Roperoller is rated for 35 pounds on 3-4mm cord. The buckle is the reason to buy this kit: a patented brass roller lets you tension by hand, re-snug it tighter after the load settles, and pop it loose one-handed when you stop. No ratchet handle to fight, and the cam grips at whatever tension you set so it won't creep loose on washboard.
To mount, weave a strap through your panel's webbing, run it over the gear, and lock the cam. Loads use a 3:1 safety factor. Note: the MOLLE board shown in the photos is not included; this kit is the straps that lash gear to it.
No se pudo cargar la disponibilidad de retiro
Overview
The Rollercam MOLLE Tie-Down Kit packs ten 0.75-inch cam straps in three lengths plus a Roperoller 2-pack, all built around Rollercam's patented brass-roller cam buckle. It is sized to secure gear to a MOLLE panel, but the straps work anywhere on the rig.
Key features
- Ten 0.75-inch cam straps: four at 2 ft, four at 3 ft, two at 6 ft
- Patented brass-roller cam buckle: 95 lb working load per strap
- Roperoller 2-pack with 20 ft of cord, plus two 10 ft sections of 3mm accessory cord (35 lb working load)
- UV-stabilized polypropylene webbing, triple-bar tack stitching, T-135 polyester thread
- Hand-tension, re-tension, and one-handed release; no ratchet hardware
Use cases
Built to strap gear to a MOLLE panel on a truck bed, rack, or door, but the lengths cover the rest of the rig too. Buyers run them on spare tires, camp fridges, traction boards, tool storage, and jerry cans. The 6-foot straps wrap bulky loads; the Roperoller and accessory cord handle bundles and odd shapes a flat strap can't.
- Cam straps: 10 total (4 × 2 ft, 4 × 3 ft, 2 × 6 ft)
- Strap width: 0.75 in
- Cam buckle working load: 95 lb
- Roperoller: 2-pack with 20 ft cord, 35 lb working load (3-4mm rope/paracord)
- Accessory cord: 2 × 10 ft sections, 3mm
- Webbing: UV-stabilized polypropylene
- Buckle: patented brass roller, stainless hardware
- Stitching: triple-bar tack
- Thread: T-135 polyester
- Safety factor: 3:1
- MOLLE board: not included
- Fulfillment: ships from Rollercam (Shopify Collective)
What's in the kit?
Ten 0.75-inch cam straps (four 2-foot, four 3-foot, and two 6-foot), a 2-pack Roperoller with 20 feet of cord, and two 10-foot sections of 3mm accessory cord.
Is the MOLLE panel included?
No. The kit is the straps and cord that lash gear to a MOLLE panel. You supply the panel.
How much weight can the straps hold?
Each 0.75-inch cam strap has a 95-pound working load. The Roperoller is rated for 35 pounds on 3-4mm cord. All ratings use a 3:1 safety factor.
How do the straps attach to a MOLLE panel?
Weave the strap through the panel's webbing rows, run it over your gear, then pull it tight and lock the cam. The strap stays put without snaps or extra hardware.
Can I re-tighten a strap after the load settles?
Yes. The cam grips at whatever tension you pull, so when gear shifts on rough trail you just snug it tighter by hand. No re-threading.
Will these hold up to saltwater and mud?
Yes. The webbing is UV-stabilized polypropylene and the buckle uses a brass roller with stainless hardware, so wet and coastal use is fine. Rinse and dry after salt or mud, and check the webbing for wear before each trip.
Are these rated for lifting or climbing?
No. These are tie-down straps only. Do not use them for overhead lifting or climbing.