Rollercam 1.25-Inch Cam Strap, Loop End
Rollercam 1.25-Inch Cam Strap, Loop End
The Rollercam 1.25-Inch Cam Strap, Loop End is a finished tie-down strap with a sewn loop on one end and Rollercam's patented cam buckle on the other. The loop lets you girth-hitch the strap straight to a fixed anchor - a roof-rack bar, a roll-cage tube, a trailer rail - so the anchor point can't slide around under the load. Webbing is 1.25 inches of high-tenacity polypropylene with UV inhibitors, rated to a 350 lb working load.
The cam buckle is the reason to run these over a ratchet. You tension by hand, so you can't crank it down hard enough to crush gear. The cam then holds the line through vibration - washboard roads, highway miles - without backing off. When you're done, lift the cam and the webbing glides free in one motion. No ratchet to reset, no knot to pick at, one-handed once you have the feel.
It ships as two loop-end pieces: the strap in your selected length plus a short loop strap that carries the cam buckle. Pick 4, 6, or 9 feet by load. Buckle hardware is a Zamak body with a marine-grade brass roller and stainless steel shaft and springs. Finish is graphite webbing with orange length markers.
No se pudo cargar la disponibilidad de retiro
Overview
A finished 1.25-inch cam strap with a sewn loop end, built to girth-hitch heavy, anchored loads to a bar or rail. The patented cam buckle re-tensions, holds without slipping under vibration, and releases one-handed - no ratchet bulk, no knots.
Key features
- 1.25-inch high-tenacity polypropylene webbing with UV inhibitors; 350 lb working load limit.
- Sewn loop end girth-hitches around fixed anchors so the strap can't shake free when the load shifts.
- Patented Rollercam cam buckle - hand-tension, holds through vibration, one-handed release.
- Hardware: Zamak buckle body, marine-grade brass roller, stainless steel shaft and springs.
- Three lengths: 4, 6, and 9 feet. Ships as two loop-end pieces (buckle piece plus selected length).
Use cases
Securing roof-rack loads, gear boxes, coolers, and firewood on overland and off-road rigs. The loop end shines anywhere you want the anchor fixed in place - girth-hitched to a roof-rack crossbar, roll-cage tube, or trailer rail - and the cam holds it there over rough ground without re-tightening.
- Webbing width: 1.25 in
- Webbing material: High-tenacity polypropylene, UV-inhibited
- Working load limit: 350 lb
- Lengths: 4 ft, 6 ft, 9 ft
- End type: Sewn loop (both pieces)
- Buckle body: Zamak
- Roller: Marine-grade brass
- Shaft and springs: Stainless steel
- Finish: Graphite webbing, orange length markers
- In the box: Two loop-end pieces - cam-buckle piece plus selected length
Will the buckle slip or rattle loose on rough roads?
No. The cam grabs the webbing and holds it. In months of regular use across highway miles and washboard forest roads, the strap did not shift.
How is the loop end different from a regular cam strap?
The sewn loop lets you girth-hitch the strap to a bar or rail: pass the buckle end through the loop and cinch. Looping the strap through itself means it can't shake free when the load moves.
Can I release it with one hand?
Yes. Lift the cam and the webbing glides free in a single motion. There is no ratchet to crank back open. Most people have it one-handed by the third load.
How much can it hold?
Each strap has a 350 lb working load limit - coolers, gear boxes, firewood, rooftop luggage. It is a securing strap, not a rated lifting or rigging sling, so don't use it to hoist a load.
Can I over-tighten it the way a ratchet does?
No. You tension by hand, so you can't crank it down hard enough to crush gear or bow a box. That is the trade for cam control: you set the tension you can pull, and the cam holds it.
What is it made of, and will it hold up in the sun?
The webbing is high-tenacity polypropylene with UV inhibitors. The buckle is a Zamak body with a marine-grade brass roller and stainless steel shaft and springs. Keep the webbing untwisted when you cinch, and tuck the loose tail so it doesn't flap.